Engine Tools
Oxygen Sensor Wrench
  
A highly specialized 22mm tool designed for removal of the Lambda sensor from your
hard to reach manifold or header. Open ring design for harness to pass through.
For use with 3/8" square drive. Manufactured by Schley Products in the USA.
Tool |
Part Number |
Price |
Order Online |
Oxygen Sensor Wrench |
10.012.88750 |
$32.95 |
Add to Basket |
Timing Belt Tensioning Tool
 
For late model cam belt idlers with pin holes. These wrenches grip the center of
the idler pulley allowing proper tensioning of the timing belt. Manufactured by Schley
Products in the USA.
Tool |
Part Number |
Price |
Order Online |
Timing Belt Tensioning Tool, <1998 |
10.012.86400 |
$22.95 |
Add to Basket |
Timing Belt Tensioning Tool, 1999-2005 |
10.012.62400 |
49.95 |
Add to Basket |
Same as above, but made by Stahlwille Germany. Lacks the nice rubber handle, but performs the same function.
Tool |
Part Number |
Price |
Order Online |
Timing Belt Tensioning Tool (Germany) |
10.012.12717 |
$16.95 |
Add to Basket |
12mm 12 Point Driver
This tool can be used to remove 12 point cylinder head bolts as well as the
special bolt that retains the fifth gear on the 020 transmission mainshaft. 1/2"
square drive. Made by Stahlwille Germany.
Tool |
Part Number |
Price |
Order Online |
12mm 12 Point Driver |
10.012.012 |
$24.95 |
Add to Basket |
Valve Spring Compressor
The Valve Spring Compressor can be used in or out of the vehicle to change springs.
Fits both 8V and 16V cylinder heads, including Mk3 and VR6. Manufactured
by Schley Products in the USA.
Tool |
Part Number |
Price |
Order Online |
Valve Spring Compressor |
10.012.91400 |
$129.95 |
Add to Basket |
Valve Seal Tool
Tool |
Part Number |
Price |
Order Online |
Valve Seal Removal Pliers (4-cyl/VR6) |
10.012.92350 |
$52.95 |
Add to Basket |
CO Mixture Tool
With this tool and two fingers, you can make all the necessary adjustments to the
idle mixture on your CIS car. The T-handle design prevents it from becoming "lost"
like Allen wrenches. Changes should be checked with an exhaust gas analyzer for
the most accurate results. Made by Stahlwille Germany.
Tool |
Part Number |
Price |
Order Online |
Adjustment Tool for Idle CO mixture |
99.012.001 |
$9.95 |
Add to Basket |
CIS Fuel Injector Remover
With the CIS injector remover and a screwdriver, you can remove the fuel
injector nozzles with a minimum of problems. The socket removal tools then
allow you to replace your cracked or dried-out injector holder. Designed for 8V
engines, but helps on 16V engines, too. Manufactured by Schley Products in the USA.
Tool |
Part Number |
Price |
Order Online |
CIS Fuel Injector Remover |
10.012.83400 |
$7.95 |
Add to Basket |
Water Pump Pulley Aid
This tool keeps the pulley stationary while removing or installing the 3 bolts
that retain it to the pump. Manufactured by Schley Products in the USA.
Tool |
Part Number |
Price |
Order Online |
Water Pump Pulley Aid |
10.012.96280 |
$31.95 |
Add to Basket |
Fan Clutch Wrenches
 10.012.62100
 10.012.61600
 10.012.63600
These uniquely designed tools are used in conjunction with part number
10.012.62100 to loosen and tighten the fan clutch on Audi & VW's. The
unique design of the 10.012.61600 works with all water pumps that have bolts
holding the pulley on the pump. On later year VW Passats, the water pump
pulley is pressed on and pins in tool part number 10.012.63600 are inserted into the
pulley to hold the water pump stationary for fan clutch removal and replacement.
The 32mm Fan Clutch Wrench 10.012.62100, works with part number
10.012.61600 on 1998-2005 Volkswagens except those using pressed on pulleys.
The 32mm Fan Clutch Wrench 10.012.62100, works with part number
10.012.63600 on 1998-2005 B5 Passat's with 2.8L V6 engines.
Tool |
Part Number |
Price |
Order Online |
Fan Clutch Wrench (use with 61600 or 63600) |
10.012.62100 |
$47.95 |
Add to Basket |
Fan Clutch Wrench for bolt-on pulleys |
10.012.61600 |
46.95 |
Add to Basket |
Fan Clutch Wrench for pressed-on pulleys |
10.012.63600 |
89.95 |
Add to Basket |
Spark Plug Boot Puller & Installer
The VW steel spark plug boots are designed to seal and increase contact
between the spark plug and spark plug wire. With the increased seal and
location of the boot, a special tool has been developed to access and remove the
spark plug boot. The tool is also needed in snapping the spark plug boot on
to the spark plug that is in a very confined area. This spark plug boot
tool was designed in hardened stainless steel for long-term service. The "T"
handle gives you plenty of pulling power to remove and replace the most difficult
spark plug boot.
Tool |
Part Number |
Price |
Order Online |
Spark Plug Boot Puller & Installer |
10.012.98180 |
$44.95 |
Add to Basket |
Valve Adjusting Tools
 
Valve adjusting on the Rabbit, Scirocco, and Jetta 1 requires the use of
a special tool to hold the cam followers in the down position in order to remove
the shims for replacement. The valve adjusting pliers are then used to remove
the shim. Note: The 1.6L and 1.7L engines use a different tool (not shown) than the
1.8L engine becuase of valve spacing. The shim set works on all solid lifter
cylinder heads. It contains an assortment of eighteen shims ranging from 3.40mm to
3.85mm in thickness.
Tool |
Part Number |
Price |
Order Online |
Valve Adjusting Tool, 1.8L |
10.012.83100 |
53.95 |
Add to Basket |
Valve Shim Pliers (Germany) |
10.012.12956 |
52.95 |
Add to Basket |
Valve Adjusting Shim Set (18 shims) |
10.012.109K |
25.00 |
Add to Basket |
G60 Specialty Tools
Autotech 68mm Pulley Tool
Autotech's high boost pulley for the G60 is designed to use this timing belt
tool to aid in the proper torquing of the pulley bolt by preventing the pulley from
turning while tightening.
Tool |
Part Number |
Price |
Order Online |
Autotech 68mm Pulley Tool |
10.012.86400 |
$22.95 |
Add to Basket |
G60 Drive Belt Tensioner Tool
This factory tool compresses the drive belt tensioner with ease, making belt and
pulley changes quick and hassle-free. We offer this tool as an outright purchase
or, when purchasing a Stage 2 or 3 kit from us, it can be returned within 30 days
as a rental for only a small fee. Contact our sales staff for rental information.
Tool |
Part Number |
Price |
Order Online |
G60 Drive Belt Tensioner Tool |
10.012.G60 |
$125.00 |
Add to Basket |
|
